11/23/2023 0 Comments Moca wifi access pointYou have the right idea: using MoCA as an ethernet bridge between your router and your new access point. Will I need to alter anything internally with the router to make this work?.Do I have the right idea for what can work? Or will I need another ethernet cable to connect the devices? If that's true, am I better off just buying a second wifi router?.|*coax outlet]-long coax cable-|->->-|Modem/Router| Proposed setup: | Back of apartment | Front of Apartment |*coax outlet]-long coax cable->-|->-|Modem/Router| Here's my current setup: | Back of apartment | Front of Apartment I only have devices connected via WiFI, save the modem/router combo I have. It's a long apartment, so the Wifi is fine in one area, but very bad in another. I live in an apartment so I can't make destructive cable home mods. In most cases, this will mean setting the TCP/IPv4 settings screen to Obtain an IP address automatically.I'm trying to figure out how best to increase the coverage of the WiFi signal inside my apartment, and stumbled across setting up a MoCA network as a possible option, but all the examples I see seem to point to using it with a lot of wired devices, or having to connect another long ethernet cable between devices. You will want to reverse the changes that you made to your computer IP settings. Note: Other computers on the network should now be able to access the AP configuration interface by opening a browser and typing the AP IP address in the browser address bar.Ĭ onfigure the wireless security settings on the AP:įor Home models, see How do I change the WiFi password or security level on my NETGEAR router? In many cases the primary DNS is the same as the Default Gateway, and the secondary can be blank.ĭisconnect the ethernet cable that connects the AP to the computer, and connect the AP to your existing network. The DNS server addresses can be left blank, or filled in with the DNS addresses for your network.The Default Gateway address can be left blank, or filled in with the default gateway address for your network.Set the IP address and Subnet Mask to suit your network.Choose an IP address that is not currently in use and is outside the range (scope) of any DHCP server on the network.In the browser address bar, type the default IP address of your AP (for example 192.168.0.100 ) and hit enter.ġ0. Note : A cross-over cable is not necessary.ĩ. Connect the computer and the AP directly together, using an Ethernet cable. Set the IP address of the computer to 192.168.0.210 and the Subnet mask to 255.255.255.0. Note the current TCP/IP settings, as you will want to set the computer back to them later.ħ. Click to highlight Internet Protocol Version 4 (TCP/IPv4).Ħ. Click Start > Control Panel > Network and Internet > Network and Sharing center > Change adaptor settings.Ĥ. For other versions of Windows, see Microsoft: Change TCP/IP Settings.įor non-Windows computers such as Apple, check your computer user manual for instructions.Ģ. Note: The following example uses a Windows 7 PC. In order to configure the AP, you will have to temporarily configure your computer to have an IP address in the same subnet as the AP default IP address. Check your computer user manual for instructions.Ĭonfigure a static IP address on your computer:ġ. Note: It is also possible to get this information using non-Windows computers, such as Apple. The last number of the IP address, 1, is the Host, and must be different on every device on the LAN. This means that the subnet is the first 3 numbers of the IP address, 192.168.2, and must be the same on every device on the LAN. In the screenshot above, the subnet mask is 255.255.255.0. Note: The Subnet Mask tells you what part of the default gateway IP address is the Subnet, and what part is the Host. In the command prompt, enter the command ipconfig. Look at the resulting output, and note your Subnet Mask and Default Gateway values. Note: If this does not work, see Microsoft: Command Prompt FAQ for more details.ģ. Doing this varies between Windows versions, but usually click the Start button and type cmd in the Search programs and files box. Connect a computer to the existing LAN. Ensure you have internet access.Ģ. You will have to change the IP address of the AP if the AP default IP address is in a different subnet than your LAN network.ĭiscover the IP subnet of the existing LAN:ġ. Click a device to see the user manual and installation guide. The default IP address of your AP will be on a sticker on the rear or bottom of the AP. This list below shows some models of NETGEAR Access Point, and their default IP address. This document talks about configuring the Access Point (AP) to be in the same IP subnet as the network, and is intended for first time users. The following article is intended to assist with the installation of a NETGEAR Access Point on an existing LAN network.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |